SC427MLTRT【PDF 26/33 页】IC REG DL BUCK/LINEAR 32MLPQ

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录46

22页 23页 24页 25页 [26页]27页 28页 29页 30页

SC417/SC427

Applications Information (continued)

Double-pulsing occurs due to switching noise seen at the

FB input or because the FB ripple voltage is too low. This

causes the FB comparator to trigger prematurely after the

250ns minimum off-time has expired. In extreme cases

the noise can cause three or more successive on-times.

Double-pulsing will result in higher ripple voltage at the

output, but in most applications it will not affect opera-

tion. This form of instability can usually be avoided by

providing the FB pin with a smooth, clean ripple signal

that is at least 10mVp-p, which may dictate the need to

increase the ESR of the output capacitors. It is also impera-

tive to provide a proper PCB layout as discussed in the

Layout Guidelines section.

Another way to eliminate doubling-pulsing is to add a

small (~ 10pF) capacitor across the upper feedback resis-

tor, as shown in Figure 13. This capacitor should be left

unpopulated until it can be confirmed that double-pulsing

exists. Adding the C

TOP

capacitor will couple more ripple

into FB to help eliminate the problem. An optional con-

nection on the PCB should be available for this capacitor.

OUT

To FB pin

TOP

Figure 13 Capacitor Coupling to FB Pin

ESR loop instability is caused by insufficient ESR. The

details of this stability issue are discussed in the ESR

Requirements section. The best method for checking sta-

bility is to apply a zero-to-full load transient and observe

the output voltage ripple envelope for overshoot and

ringing. Ringing for more than one cycle after the initial

step is an indication that the ESR should be increased.

One simple way to solve this problem is to add trace resis-

tance in the high current output path. A side effect of

adding trace resistance is a decrease in load regulation.

ESR Requirements

A minimum ESR is required for two reasons. One reason is

to generate enough output ripple voltage to provide

10mVp-p at the FB pin (after the resistor divider) to avoid

double-pulsing.

The second reason is to prevent instability due to insuffi-

cient ESR. The on-time control regulates the valley of the

output ripple voltage. This ripple voltage is the sum of the

two voltages. One is the ripple generated by the ESR, the

other is the ripple due to capacitive charging and dis-

charging during the switching cycle. For most applica-

tions the minimum ESR ripple voltage is dominated by the

output capacitors, typically SP or POSCAP devices. For

stability the ESR zero of the output capacitor should be

lower than approximately one-third the switching fre-

quency. The formula for minimum ESR is shown by the

following equation.

OUT

MIN

Using Ceramic Output Capacitors

For applications using ceramic output capacitors, the ESR

is normally too small to meet the above ESR criteria. In

these applications it is necessary to add a small virtual ESR

network composed of two capacitors and one resistor, as

shown in Figure 14. This network creates a ramp voltage

across C

, analogous to the ramp voltage generated across

the ESR of a standard capacitor. This ramp is then capaci-

tively coupled into the FB pin via capacitor C

OUT

Low-

side

High-

side

Figure 14 Virtual ESR Ramp Current

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式